gpiopower1: resetting system


U-Boot molsen-2018-10-05 (Oct 05 2018 - 17:02:05)

CPU0:  P5020, Version: 2.0, (0x82200020)
Core:  e5500, Version: 1.2, (0x80240012)
Clock Configuration:
       CPU0:2000 MHz, CPU1:2000 MHz, 
       CCB:800  MHz,
       DDR:666.667 MHz (1333.333 MT/s data rate) (Asynchronous), LBC:50   MHz
       FMAN1: 500 MHz
       QMAN:  400 MHz
       PME:   400 MHz
L1:    D-cache 32 KiB enabled
       I-cache 32 KiB enabled
Reset Configuration Word (RCW):
       00000000: 0c540000 00000000 1e1e0000 00000000
       00000010: 44808c00 ff002000 68000000 45000000
       00000020: 00000000 00000000 00000000 0003000f
       00000030: a0000000 00000000 00000000 00000000
Board: CYRUS
36-bit Addressing
I2C:   ready
SPI:   ready
DRAM:  Initializing....using SPD
Detected UDIMM F3-12800CL9-4GBXL
Detected UDIMM F3-12800CL9-4GBXL
6 GiB left unmapped
8 GiB (DDR3, 64-bit, CL=9, ECC off)
       DDR Controller Interleaving Mode: cache line
       DDR Chip-Select Interleaving Mode: CS0+CS1

Local Bus Controller Registers
BR0	0xE0001001	OR0	0xFFF00010
BR1	0xE1001001	OR1	0xFFF00010
BR2	0x00000000	OR2	0x00000000
BR3	0x00000000	OR3	0x00000000
BR4	0x00000000	OR4	0x00000000
BR5	0x00000000	OR5	0x00000000
BR6	0x00000000	OR6	0x00000000
BR7	0x00000000	OR7	0x00000000
LBCR	0x40000000	LCRR	0x80010004
L2:    512 KiB enabled
Corenet Platform Cache: 2 MiB enabled
SERDES: bank 2 disabled
MMC:  FSL_SDHC: 0
Board Revision dead
MAC: 00:04:A3:6B:44:93
MAC: 00:1E:C0:F7:D0:82
EEPROM: NXID v0
PCIe1: Root Complex, x4 gen1, regs @ 0xfe200000
  01:00.0     - 1002:9442 - Display controller
  01:00.1     - 1002:aa30 - Multimedia device
PCIe1: Bus 00 - 01
PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000
  03:00.0     - 111d:8092 - Bridge device
   04:01.0    - 111d:8092 - Bridge device
    05:00.0   - 12d8:e111 - Bridge device
   04:02.0    - 111d:8092 - Bridge device
    07:00.0   - 1102:0012 - Multimedia device
   04:03.0    - 111d:8092 - Bridge device
   04:08.0    - 111d:8092 - Bridge device
   04:10.0    - 111d:8092 - Bridge device
PCIe2: Bus 02 - 0a
PCIe3: disabled
PCIe4: disabled
Looking for VGA
PINS: 0xfc000808
videoboot: Booting PCI video card bus 1, function 0, device 0
Begin BIOS POST
End BIOS POST
Setting VESA Mode
Found required VESA mode
About to set mode 279
About to get mode
Got mode 49431 (0xc117)
OK
XSize = 1024 YSize = 768 Base =0xe0000000
mmio_base = 0x80000000
bgx = 0xad55ad55 fgx = 0x0
In:    serial
Out:   serial
Err:   serial
ID: NXID v0
SN: 116370042
UID: 4429431001910051e8cda080a0800000
Errata: ?????	VR?
Build date: 2016/03/11 09:56:52 
CRC: e2497539
SCSI:  scanning bus for devices...
Found 0 device(s).
Net:   Initializing Fman

MMC read: dev # 0, block # 56985, count 128 ...
Fman1: Uploading microcode version 106.1.0
Tuning PHY @ 3
Tuning PHY @ 7
FM1@DTSEC4 [PRIME], FM1@DTSEC5
X5000>