SIGTERM received, booting... [ 57.840412] kexec_core: Starting new kernel [ 0.000000] dt-cpu-ftrs: setup for ISA 3000 [ 0.000000] dt-cpu-ftrs: not enabling: system-call-vectored (disabled or unsupported by kernel) [ 0.000000] dt-cpu-ftrs: final cpu/mmu features = 0x0000f86f8f5fb1a7 0x3c006041 [ 0.000000] radix-mmu: Page sizes from device-tree: [ 0.000000] radix-mmu: Page size shift = 12 AP=0x0 [ 0.000000] radix-mmu: Page size shift = 16 AP=0x5 [ 0.000000] radix-mmu: Page size shift = 21 AP=0x1 [ 0.000000] radix-mmu: Page size shift = 30 AP=0x2 [ 0.000000] radix-mmu: Activating Kernel Userspace Execution Prevention [ 0.000000] radix-mmu: Activating Kernel Userspace Access Prevention [ 0.000000] radix-mmu: Initializing Radix MMU [ 0.000000] radix-mmu: Partition table (____ptrval____) [ 0.000000] radix-mmu: Mapped 0x0000000000000000-0x0000000040000000 with 1.00 GiB pages (exec) [ 0.000000] radix-mmu: Mapped 0x0000000040000000-0x0000001000000000 with 1.00 GiB pages [ 0.000000] radix-mmu: Process table (____ptrval____) and radix root for kernel: (____ptrval____) [ 0.000000] Linux version 5.2.11_1 (q66@moca) (gcc version 9.1.0 (GCC)) #1 SMP Thu Aug 29 18:50:48 UTC 2019 [ 0.000000] Found initrd at 0xc000000003ae0000:0xc000000006d57054 [ 0.000000] OPAL: Found memory mapped LPC bus on chip 0 [ 0.000000] Using PowerNV machine description [ 0.000000] printk: bootconsole [udbg0] enabled [ 0.000000] CPU maps initialized for 4 threads per core [ 0.000000] ----------------------------------------------------- [ 0.000000] phys_mem_size = 0x1000000000 [ 0.000000] dcache_bsize = 0x80 [ 0.000000] icache_bsize = 0x80 [ 0.000000] cpu_features = 0x0000f86f8f5fb1a7 [ 0.000000] possible = 0x0000fbffcf5fb1a7 [ 0.000000] always = 0x00000003800081a1 [ 0.000000] cpu_user_features = 0xdc0065c2 0xaee00000 [ 0.000000] mmu_features = 0xbc006041 [ 0.000000] firmware_features = 0x0000000110000000 [ 0.000000] hash-mmu: ppc64_pft_size = 0x0 [ 0.000000] hash-mmu: kernel vmalloc start = 0xc008000000000000 [ 0.000000] hash-mmu: kernel IO start = 0xc00a000000000000 [ 0.000000] hash-mmu: kernel vmemmap start = 0xc00c000000000000 [ 0.000000] ----------------------------------------------------- [ 0.000000] cma: Reserved 3280 MiB at 0x0000000f2f000000 [ 0.000000] numa: NODE_DATA [mem 0xfff4a4500-0xfff4abfff] [ 0.000000] rfi-flush: mttrig type flush available [ 0.000000] count-cache-flush: software flush disabled. [ 0.000000] stf-barrier: eieio barrier available [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0000000) [ 0.000000] PCI host bridge /pciex@600c3c0000000 (primary) ranges: [ 0.000000] MEM 0x000600c000000000..0x000600c07ffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006000000000000..0x0006003fffffffff -> 0x0006000000000000 (M64 #1..31) [ 0.000000] Using M64 #31 as default window [ 0.000000] 512 (511) PE's M32: 0x80000000 [segment=0x400000] [ 0.000000] M64: 0x4000000000 [segment=0x20000000] [ 0.000000] Allocated bitmap for 4088 MSIs (base IRQ 0xfe000) [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0100000) [ 0.000000] PCI host bridge /pciex@600c3c0100000 ranges: [ 0.000000] MEM 0x000600c080000000..0x000600c0fffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006004000000000..0x0006007fffffffff -> 0x0006004000000000 (M64 #1..15) [ 0.000000] Using M64 #15 as default window [ 0.000000] 256 (255) PE's M32: 0x80000000 [segment=0x800000] [ 0.000000] M64: 0x4000000000 [segment=0x40000000] [ 0.000000] Allocated bitmap for 2040 MSIs (base IRQ 0xfd800) [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0200000) [ 0.000000] PCI host bridge /pciex@600c3c0200000 ranges: [ 0.000000] MEM 0x000600c100000000..0x000600c17ffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006008000000000..0x000600bfffffffff -> 0x0006008000000000 (M64 #1..15) [ 0.000000] Using M64 #15 as default window [ 0.000000] 256 (255) PE's M32: 0x80000000 [segment=0x800000] [ 0.000000] M64: 0x4000000000 [segment=0x40000000] [ 0.000000] Allocated bitmap for 2040 MSIs (base IRQ 0xfd000) [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0300000) [ 0.000000] PCI host bridge /pciex@600c3c0300000 ranges: [ 0.000000] MEM 0x000600c180000000..0x000600c1fffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006020000000000..0x0006023fffffffff -> 0x0006020000000000 (M64 #1..31) [ 0.000000] Using M64 #31 as default window [ 0.000000] 512 (511) PE's M32: 0x80000000 [segment=0x400000] [ 0.000000] M64: 0x4000000000 [segment=0x20000000] [ 0.000000] Allocated bitmap for 4088 MSIs (base IRQ 0xfc000) [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0400000) [ 0.000000] PCI host bridge /pciex@600c3c0400000 ranges: [ 0.000000] MEM 0x000600c200000000..0x000600c27ffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006024000000000..0x0006027fffffffff -> 0x0006024000000000 (M64 #1..15) [ 0.000000] Using M64 #15 as default window [ 0.000000] 256 (255) PE's M32: 0x80000000 [segment=0x800000] [ 0.000000] M64: 0x4000000000 [segment=0x40000000] [ 0.000000] Allocated bitmap for 2040 MSIs (base IRQ 0xfb800) [ 0.000000] Initializing IODA2 PHB (/pciex@600c3c0500000) [ 0.000000] PCI host bridge /pciex@600c3c0500000 ranges: [ 0.000000] MEM 0x000600c280000000..0x000600c2fffeffff -> 0x0000000080000000 [ 0.000000] MEM 0x0006028000000000..0x000602bfffffffff -> 0x0006028000000000 (M64 #1..15) [ 0.000000] Using M64 #15 as default window [ 0.000000] 256 (255) PE's M32: 0x80000000 [segment=0x800000] [ 0.000000] M64: 0x4000000000 [segment=0x40000000] [ 0.000000] Allocated bitmap for 2040 MSIs (base IRQ 0xfb000) [ 0.000000] OPAL nvram setup, 589824 bytes [ 0.000000] barrier-nospec: using ORI speculation barrier [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000fffffffff] [ 0.000000] Device empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000fffffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000fffffffff] [ 0.000000] percpu: Embedded 43 pages/cpu s138776 r0 d37352 u176128 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16515072 [ 0.000000] Policy zone: Normal [ 0.000000] Kernel command line: root=live:CDLABEL=VOID_LIVE ro init=/sbin/init \ [ 0.000000] Memory: 62496964K/67108864K available (11804K kernel code, 1492K rwdata, 2632K rodata, 4020K init, 2423K bss, 1253180K reserved, 3358720K cma-reserved) [ 0.000000] random: get_random_u64 called from __kmem_cache_create+0x60/0x7c0 with crng_init=0 [ 0.000000] SLUB: HWalign=128, Order=0-3, MinObjects=0, CPUs=32, Nodes=1 [ 0.000000] ftrace: allocating 30954 entries in 183 pages [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU restricting CPUs from NR_CPUS=2048 to nr_cpu_ids=32. [ 0.000000] Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. [ 0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=32 [ 0.000000] NR_IRQS: 512, nr_irqs: 512, preallocated irqs: 16 [ 0.000000] xive: Interrupt handling initialized with native backend [ 0.000000] xive: Using priority 7 for all interrupts [ 0.000000] xive: Using 4kB queues [ 0.000003] time_init: 56 bit decrementer (max: 7fffffffffffff) [ 0.005162] clocksource: timebase: mask: 0xffffffffffffffff max_cycles: 0x761537d007, max_idle_ns: 440795202126 ns [ 0.012428] clocksource: timebase mult[1f40000] shift[24] registered [ 0.013659] Console: colour dummy device 80x25 [ 0.016869] printk: console [hvc0] enabled [ 0.016869] printk: console [hvc0] enabled [ 0.023026] printk: bootconsole [udbg0] disabled [ 0.023026] printk: bootconsole [udbg0] disabled [ 0.027216] pid_max: default: 32768 minimum: 301 [ 0.027294] LSM: Security Framework initializing [ 0.027318] Yama: becoming mindful. [ 0.032843] Dentry cache hash table entries: 8388608 (order: 14, 67108864 bytes) [ 0.035661] Inode-cache hash table entries: 4194304 (order: 13, 33554432 bytes) [ 0.035797] Mount-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.035908] Mountpoint-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 0.036166] *** VALIDATE proc *** [ 0.036279] *** VALIDATE cgroup1 *** [ 0.036299] *** VALIDATE cgroup2 *** [ 0.036590] EEH: PowerNV platform initialized [ 0.036613] POWER9 performance monitor hardware support registered [ 0.036657] rcu: Hierarchical SRCU implementation. [ 0.037472] smp: Bringing up secondary CPUs ... [ 0.050924] smp: Brought up 1 node, 32 CPUs [ 0.050945] numa: Node 0 CPUs: 0-31 [ 0.050956] Using standard scheduler topology [ 0.053417] devtmpfs: initialized [ 0.067513] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.067625] futex hash table entries: 8192 (order: 8, 1048576 bytes) [ 0.082515] pinctrl core: initialized pinctrl subsystem [ 0.082902] NET: Registered protocol family 16 [ 0.083233] audit: initializing netlink subsys (disabled) [ 0.083297] audit: type=2000 audit(1575249817.064:1): state=initialized audit_enabled=0 res=1 [ 0.083523] cpuidle: using governor ladder [ 0.083586] cpuidle: using governor menu [ 0.083659] pstore: Registered nvram as persistent store backend [ 0.089236] PCI: Probing PCI hardware [ 0.089310] PCI host bridge to bus 0000:00 [ 0.089325] pci_bus 0000:00: root bus resource [mem 0x600c000000000-0x600c07ffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.089359] pci_bus 0000:00: root bus resource [mem 0x6000000000000-0x6003fbfffffff 64bit pref] [ 0.089402] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.089428] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to ff [ 0.089486] pci 0000:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.089723] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 0.092944] pci 0000:01:00.0: [1002:67df] type 00 class 0x030000 [ 0.093051] pci 0000:01:00.0: reg 0x10: [mem 0x6000000000000-0x60001ffffffff 64bit pref] [ 0.093128] pci 0000:01:00.0: reg 0x18: [mem 0x6000200000000-0x60002001fffff 64bit pref] [ 0.093162] pci 0000:01:00.0: reg 0x20: [io 0x0000-0x00ff] [ 0.093213] pci 0000:01:00.0: reg 0x24: [mem 0x600c000000000-0x600c00003ffff] [ 0.093269] pci 0000:01:00.0: reg 0x30: [mem 0x600c000040000-0x600c00005ffff pref] [ 0.093557] pci 0000:01:00.0: supports D1 D2 [ 0.093578] pci 0000:01:00.0: PME# supported from D1 D2 D3hot D3cold [ 0.093769] pci 0000:01:00.0: 32.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x16 link at 0000:00:00.0 (capable of 126.016 Gb/s with 8 GT/s x16 link) [ 0.093984] pci 0000:01:00.1: [1002:aaf0] type 00 class 0x040300 [ 0.094068] pci 0000:01:00.1: reg 0x10: [mem 0x600c000060000-0x600c000063fff 64bit] [ 0.094367] pci 0000:01:00.1: supports D1 D2 [ 0.097480] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.097576] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.097650] PCI host bridge to bus 0001:00 [ 0.097682] pci_bus 0001:00: root bus resource [mem 0x600c080000000-0x600c0fffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.097746] pci_bus 0001:00: root bus resource [mem 0x6004000000000-0x6007f7fffffff 64bit pref] [ 0.097796] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.097821] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff [ 0.097869] pci 0001:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.098063] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold [ 0.104091] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.104142] pci_bus 0001:00: busn_res: [bus 00-ff] end is updated to ff [ 0.104208] PCI host bridge to bus 0002:00 [ 0.104243] pci_bus 0002:00: root bus resource [mem 0x600c100000000-0x600c17ffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.104305] pci_bus 0002:00: root bus resource [mem 0x6008000000000-0x600bf7fffffff 64bit pref] [ 0.104364] pci_bus 0002:00: root bus resource [bus 00-ff] [ 0.104397] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to ff [ 0.104454] pci 0002:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.104680] pci 0002:00:00.0: PME# supported from D0 D3hot D3cold [ 0.104814] random: fast init done [ 0.107863] pci 0002:01:00.0: [1b4b:9235] type 00 class 0x010601 [ 0.107920] pci 0002:01:00.0: reg 0x10: [io 0x8000-0x8007] [ 0.107948] pci 0002:01:00.0: reg 0x14: [io 0x8040-0x8043] [ 0.107989] pci 0002:01:00.0: reg 0x18: [io 0x8100-0x8107] [ 0.108021] pci 0002:01:00.0: reg 0x1c: [io 0x8140-0x8143] [ 0.108072] pci 0002:01:00.0: reg 0x20: [io 0x800000-0x80001f] [ 0.108107] pci 0002:01:00.0: reg 0x24: [mem 0x600c100000000-0x600c1000007ff] [ 0.108139] pci 0002:01:00.0: reg 0x30: [mem 0x600c150000000-0x600c15000ffff pref] [ 0.108203] pci 0002:01:00.0: BAR5 [mem size 0x00000800]: requesting alignment to 0x1000 [ 0.108311] pci 0002:01:00.0: PME# supported from D3hot [ 0.111396] pci 0002:00:00.0: PCI bridge to [bus 01] [ 0.111471] pci_bus 0002:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.111531] PCI host bridge to bus 0003:00 [ 0.111544] pci_bus 0003:00: root bus resource [mem 0x600c180000000-0x600c1fffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.111585] pci_bus 0003:00: root bus resource [mem 0x6020000000000-0x6023fbfffffff 64bit pref] [ 0.111604] pci_bus 0003:00: root bus resource [bus 00-ff] [ 0.111629] pci_bus 0003:00: busn_res: [bus 00-ff] end is updated to ff [ 0.111698] pci 0003:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.111902] pci 0003:00:00.0: PME# supported from D0 D3hot D3cold [ 0.115078] pci 0003:01:00.0: [104c:8241] type 00 class 0x0c0330 [ 0.115152] pci 0003:01:00.0: reg 0x10: [mem 0x600c180000000-0x600c18000ffff 64bit] [ 0.115204] pci 0003:01:00.0: reg 0x18: [mem 0x600c180010000-0x600c180011fff 64bit] [ 0.115408] pci 0003:01:00.0: supports D1 D2 [ 0.115432] pci 0003:01:00.0: PME# supported from D0 D1 D2 D3hot [ 0.118546] pci 0003:00:00.0: PCI bridge to [bus 01] [ 0.118625] pci_bus 0003:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.118702] PCI host bridge to bus 0004:00 [ 0.118733] pci_bus 0004:00: root bus resource [mem 0x600c200000000-0x600c27ffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.118785] pci_bus 0004:00: root bus resource [mem 0x6024000000000-0x6027f7fffffff 64bit pref] [ 0.118816] pci_bus 0004:00: root bus resource [bus 00-ff] [ 0.118851] pci_bus 0004:00: busn_res: [bus 00-ff] end is updated to ff [ 0.118917] pci 0004:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.119133] pci 0004:00:00.0: PME# supported from D0 D3hot D3cold [ 0.122301] pci 0004:01:00.0: [14e4:1657] type 00 class 0x020000 [ 0.122378] pci 0004:01:00.0: reg 0x10: [mem 0x6024000000000-0x602400000ffff 64bit pref] [ 0.122430] pci 0004:01:00.0: reg 0x18: [mem 0x6024000010000-0x602400001ffff 64bit pref] [ 0.122491] pci 0004:01:00.0: reg 0x20: [mem 0x6024000020000-0x602400002ffff 64bit pref] [ 0.122747] pci 0004:01:00.0: PME# supported from D0 D3hot D3cold [ 0.122855] pci 0004:01:00.0: 8.000 Gb/s available PCIe bandwidth, limited by 5 GT/s x2 link at 0004:00:00.0 (capable of 16.000 Gb/s with 5 GT/s x4 link) [ 0.123003] pci 0004:01:00.1: [14e4:1657] type 00 class 0x020000 [ 0.123089] pci 0004:01:00.1: reg 0x10: [mem 0x6024000030000-0x602400003ffff 64bit pref] [ 0.123160] pci 0004:01:00.1: reg 0x18: [mem 0x6024000040000-0x602400004ffff 64bit pref] [ 0.123224] pci 0004:01:00.1: reg 0x20: [mem 0x6024000050000-0x602400005ffff 64bit pref] [ 0.123462] pci 0004:01:00.1: PME# supported from D0 D3hot D3cold [ 0.123656] pci 0004:01:00.2: [14e4:1657] type 00 class 0x020000 [ 0.123743] pci 0004:01:00.2: reg 0x10: [mem 0x6024000060000-0x602400006ffff 64bit pref] [ 0.123808] pci 0004:01:00.2: reg 0x18: [mem 0x6024000070000-0x602400007ffff 64bit pref] [ 0.123880] pci 0004:01:00.2: reg 0x20: [mem 0x6024000080000-0x602400008ffff 64bit pref] [ 0.124129] pci 0004:01:00.2: PME# supported from D0 D3hot D3cold [ 0.127231] pci 0004:00:00.0: PCI bridge to [bus 01] [ 0.127333] pci_bus 0004:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.127404] PCI host bridge to bus 0005:00 [ 0.127427] pci_bus 0005:00: root bus resource [mem 0x600c280000000-0x600c2fffeffff] (bus address [0x80000000-0xfffeffff]) [ 0.127468] pci_bus 0005:00: root bus resource [mem 0x6028000000000-0x602bf7fffffff 64bit pref] [ 0.127519] pci_bus 0005:00: root bus resource [bus 00-ff] [ 0.127554] pci_bus 0005:00: busn_res: [bus 00-ff] end is updated to ff [ 0.127603] pci 0005:00:00.0: [1014:04c1] type 01 class 0x060400 [ 0.127817] pci 0005:00:00.0: PME# supported from D0 D3hot D3cold [ 0.130981] pci 0005:01:00.0: [1a03:1150] type 01 class 0x060400 [ 0.131252] pci 0005:01:00.0: supports D1 D2 [ 0.131272] pci 0005:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.134354] pci 0005:00:00.0: PCI bridge to [bus 01-02] [ 0.134494] pci_bus 0005:02: extended config space not accessible [ 0.134565] pci 0005:02:00.0: [1a03:2000] type 00 class 0x030000 [ 0.134632] pci 0005:02:00.0: reg 0x10: [mem 0x600c280000000-0x600c280ffffff] [ 0.134685] pci 0005:02:00.0: reg 0x14: [mem 0x600c281000000-0x600c28101ffff] [ 0.134752] pci 0005:02:00.0: reg 0x18: [io 0x0000-0x007f] [ 0.134944] pci 0005:02:00.0: supports D1 D2 [ 0.134981] pci 0005:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.138008] pci 0005:01:00.0: PCI bridge to [bus 02] [ 0.138084] pci_bus 0005:00: busn_res: [bus 00-ff] end is updated to 02 [ 0.138114] pci 0000:00:00.0: BAR 15: assigned [mem 0x6000000000000-0x60002ffffffff 64bit pref] [ 0.138147] pci 0000:00:00.0: BAR 14: assigned [mem 0x600c000000000-0x600c0003fffff] [ 0.138195] pci 0000:00:00.0: BAR 13: no space for [io size 0x1000] [ 0.138221] pci 0000:00:00.0: BAR 13: failed to assign [io size 0x1000] [ 0.138268] pci 0000:01:00.0: BAR 0: assigned [mem 0x6000000000000-0x60001ffffffff 64bit pref] [ 0.138337] pci 0000:01:00.0: BAR 2: assigned [mem 0x6000200000000-0x60002001fffff 64bit pref] [ 0.138383] pci 0000:01:00.0: BAR 5: assigned [mem 0x600c000000000-0x600c00003ffff] [ 0.138406] pci 0000:01:00.0: BAR 6: assigned [mem 0x600c000040000-0x600c00005ffff pref] [ 0.138424] pci 0000:01:00.1: BAR 0: assigned [mem 0x600c000060000-0x600c000063fff 64bit] [ 0.138477] pci 0000:01:00.0: BAR 4: no space for [io size 0x0100] [ 0.138502] pci 0000:01:00.0: BAR 4: failed to assign [io size 0x0100] [ 0.138542] pci 0000:00 : [PE# 1fe] Secondary bus 0x0000000000000000 associated with PE#1fe [ 0.138834] pci 0000:01 : [PE# 00] Secondary bus 0x0000000000000001 associated with PE#0 [ 0.139292] pci 0000:01 : [PE# 00] Setting up 32-bit TCE table at 0..80000000 [ 0.148247] IOMMU table initialized, virtual merging enabled [ 0.148269] pci 0000:01 : [PE# 00] Setting up window#0 0..7fffffff pg=1000 [ 0.148290] pci 0000:01 : [PE# 00] Enabling 64-bit DMA bypass [ 0.148314] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.148342] pci 0000:00:00.0: bridge window [mem 0x600c000000000-0x600c07fefffff] [ 0.148370] pci 0000:00:00.0: bridge window [mem 0x6000000000000-0x6003fbff0ffff 64bit pref] [ 0.148418] pci_bus 0000:00: Some PCI device resources are unassigned, try booting with pci=realloc [ 0.148467] pci_bus 0000:00: resource 4 [mem 0x600c000000000-0x600c07ffeffff] [ 0.148506] pci_bus 0000:00: resource 5 [mem 0x6000000000000-0x6003fbfffffff 64bit pref] [ 0.148554] pci_bus 0000:01: resource 1 [mem 0x600c000000000-0x600c07fefffff] [ 0.148602] pci_bus 0000:01: resource 2 [mem 0x6000000000000-0x6003fbff0ffff 64bit pref] [ 0.148655] pci 0001:00 : [PE# fe] Secondary bus 0x0000000000000000 associated with PE#fe [ 0.148904] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.148954] pci_bus 0001:00: resource 4 [mem 0x600c080000000-0x600c0fffeffff] [ 0.148995] pci_bus 0001:00: resource 5 [mem 0x6004000000000-0x6007f7fffffff 64bit pref] [ 0.149047] pci 0002:00:00.0: BAR 14: assigned [mem 0x600c100000000-0x600c1007fffff] [ 0.149076] pci 0002:00:00.0: BAR 13: no space for [io size 0x1000] [ 0.149111] pci 0002:00:00.0: BAR 13: failed to assign [io size 0x1000] [ 0.149150] pci 0002:01:00.0: BAR 6: assigned [mem 0x600c100000000-0x600c10000ffff pref] [ 0.149210] pci 0002:01:00.0: BAR 5: assigned [mem 0x600c100010000-0x600c1000107ff] [ 0.149261] pci 0002:01:00.0: BAR 4: no space for [io size 0x0020] [ 0.149293] pci 0002:01:00.0: BAR 4: failed to assign [io size 0x0020] [ 0.149321] pci 0002:01:00.0: BAR 0: no space for [io size 0x0008] [ 0.149335] pci 0002:01:00.0: BAR 0: failed to assign [io size 0x0008] [ 0.149372] pci 0002:01:00.0: BAR 2: no space for [io size 0x0008] [ 0.149418] pci 0002:01:00.0: BAR 2: failed to assign [io size 0x0008] [ 0.149452] pci 0002:01:00.0: BAR 1: no space for [io size 0x0004] [ 0.149487] pci 0002:01:00.0: BAR 1: failed to assign [io size 0x0004] [ 0.149523] pci 0002:01:00.0: BAR 3: no space for [io size 0x0004] [ 0.149557] pci 0002:01:00.0: BAR 3: failed to assign [io size 0x0004] [ 0.149592] pci 0002:00 : [PE# fe] Secondary bus 0x0000000000000000 associated with PE#fe [ 0.149837] pci 0002:01 : [PE# fd] Secondary bus 0x0000000000000001 associated with PE#fd [ 0.150093] pci 0002:01 : [PE# fd] Setting up 32-bit TCE table at 0..80000000 [ 0.159067] pci 0002:01 : [PE# fd] Setting up window#0 0..7fffffff pg=1000 [ 0.159090] pci 0002:01 : [PE# fd] Enabling 64-bit DMA bypass [ 0.159116] pci 0002:00:00.0: PCI bridge to [bus 01] [ 0.159135] pci 0002:00:00.0: bridge window [mem 0x600c100000000-0x600c17fefffff] [ 0.159171] pci_bus 0002:00: Some PCI device resources are unassigned, try booting with pci=realloc [ 0.159205] pci_bus 0002:00: resource 4 [mem 0x600c100000000-0x600c17ffeffff] [ 0.159253] pci_bus 0002:00: resource 5 [mem 0x6008000000000-0x600bf7fffffff 64bit pref] [ 0.159281] pci_bus 0002:01: resource 1 [mem 0x600c100000000-0x600c17fefffff] [ 0.159301] pci 0003:00:00.0: BAR 14: assigned [mem 0x600c180000000-0x600c1803fffff] [ 0.159349] pci 0003:01:00.0: BAR 0: assigned [mem 0x600c180000000-0x600c18000ffff 64bit] [ 0.159396] pci 0003:01:00.0: BAR 2: assigned [mem 0x600c180010000-0x600c180011fff 64bit] [ 0.159462] pci 0003:00 : [PE# 1fe] Secondary bus 0x0000000000000000 associated with PE#1fe [ 0.159698] pci 0003:01 : [PE# 1fd] Secondary bus 0x0000000000000001 associated with PE#1fd [ 0.159945] pci 0003:01 : [PE# 1fd] Setting up 32-bit TCE table at 0..80000000 [ 0.168890] pci 0003:01 : [PE# 1fd] Setting up window#0 0..7fffffff pg=1000 [ 0.168918] pci 0003:01 : [PE# 1fd] Enabling 64-bit DMA bypass [ 0.168934] pci 0003:00:00.0: PCI bridge to [bus 01] [ 0.168965] pci 0003:00:00.0: bridge window [mem 0x600c180000000-0x600c1ffefffff] [ 0.169012] pci_bus 0003:00: resource 4 [mem 0x600c180000000-0x600c1fffeffff] [ 0.169061] pci_bus 0003:00: resource 5 [mem 0x6020000000000-0x6023fbfffffff 64bit pref] [ 0.169110] pci_bus 0003:01: resource 1 [mem 0x600c180000000-0x600c1ffefffff] [ 0.169153] pci 0004:00:00.0: BAR 15: assigned [mem 0x6024000000000-0x602403fffffff 64bit pref] [ 0.169203] pci 0004:01:00.0: BAR 0: assigned [mem 0x6024000000000-0x602400000ffff 64bit pref] [ 0.169273] pci 0004:01:00.0: BAR 2: assigned [mem 0x6024000010000-0x602400001ffff 64bit pref] [ 0.169317] pci 0004:01:00.0: BAR 4: assigned [mem 0x6024000020000-0x602400002ffff 64bit pref] [ 0.169372] pci 0004:01:00.1: BAR 0: assigned [mem 0x6024000030000-0x602400003ffff 64bit pref] [ 0.169427] pci 0004:01:00.1: BAR 2: assigned [mem 0x6024000040000-0x602400004ffff 64bit pref] [ 0.169482] pci 0004:01:00.1: BAR 4: assigned [mem 0x6024000050000-0x602400005ffff 64bit pref] [ 0.169545] pci 0004:01:00.2: BAR 0: assigned [mem 0x6024000060000-0x602400006ffff 64bit pref] [ 0.169612] pci 0004:01:00.2: BAR 2: assigned [mem 0x6024000070000-0x602400007ffff 64bit pref] [ 0.169660] pci 0004:01:00.2: BAR 4: assigned [mem 0x6024000080000-0x602400008ffff 64bit pref] [ 0.169715] pci 0004:00 : [PE# fe] Secondary bus 0x0000000000000000 associated with PE#fe [ 0.169959] pci 0004:01 : [PE# 00] Secondary bus 0x0000000000000001 associated with PE#0 [ 0.170202] pci 0004:01 : [PE# 00] Setting up 32-bit TCE table at 0..80000000 [ 0.179163] pci 0004:01 : [PE# 00] Setting up window#0 0..7fffffff pg=1000 [ 0.179188] pci 0004:01 : [PE# 00] Enabling 64-bit DMA bypass [ 0.179204] pci 0004:00:00.0: PCI bridge to [bus 01] [ 0.179238] pci 0004:00:00.0: bridge window [mem 0x6024000000000-0x6027f7fffffff 64bit pref] [ 0.179274] pci_bus 0004:00: resource 4 [mem 0x600c200000000-0x600c27ffeffff] [ 0.179301] pci_bus 0004:00: resource 5 [mem 0x6024000000000-0x6027f7fffffff 64bit pref] [ 0.179330] pci_bus 0004:01: resource 2 [mem 0x6024000000000-0x6027f7fffffff 64bit pref] [ 0.179352] pci 0005:00:00.0: BAR 14: assigned [mem 0x600c280000000-0x600c2817fffff] [ 0.179397] pci 0005:00:00.0: BAR 13: no space for [io size 0x1000] [ 0.179445] pci 0005:00:00.0: BAR 13: failed to assign [io size 0x1000] [ 0.179473] pci 0005:01:00.0: BAR 14: assigned [mem 0x600c280000000-0x600c2817fffff] [ 0.179503] pci 0005:01:00.0: BAR 13: no space for [io size 0x1000] [ 0.179517] pci 0005:01:00.0: BAR 13: failed to assign [io size 0x1000] [ 0.179533] pci 0005:02:00.0: BAR 0: assigned [mem 0x600c280000000-0x600c280ffffff] [ 0.179580] pci 0005:02:00.0: BAR 1: assigned [mem 0x600c281000000-0x600c28101ffff] [ 0.179618] pci 0005:02:00.0: BAR 2: no space for [io size 0x0080] [ 0.179644] pci 0005:02:00.0: BAR 2: failed to assign [io size 0x0080] [ 0.179682] pci 0005:00 : [PE# fe] Secondary bus 0x0000000000000000 associated with PE#fe [ 0.179942] pci 0005:02 : [PE# fd] Secondary bus 0x0000000000000002..0x0000000000000002 associated with PE#fd [ 0.180203] pci 0005:02 : [PE# fd] Setting up 32-bit TCE table at 0..80000000 [ 0.189142] pci 0005:02 : [PE# fd] Setting up window#0 0..7fffffff pg=1000 [ 0.189167] pci 0005:02 : [PE# fd] Enabling 64-bit DMA bypass [ 0.189192] pci 0005:01:00.0: PCI bridge to [bus 02] [ 0.189212] pci 0005:01:00.0: bridge window [mem 0x600c280000000-0x600c2ffefffff] [ 0.189253] pci 0005:01 : [PE# fc] Secondary bus 0x0000000000000001 associated with PE#fc [ 0.189486] pci 0005:00:00.0: PCI bridge to [bus 01-02] [ 0.189516] pci 0005:00:00.0: bridge window [mem 0x600c280000000-0x600c2ffefffff] [ 0.189577] pci_bus 0005:00: Some PCI device resources are unassigned, try booting with pci=realloc [ 0.189610] pci_bus 0005:00: resource 4 [mem 0x600c280000000-0x600c2fffeffff] [ 0.189649] pci_bus 0005:00: resource 5 [mem 0x6028000000000-0x602bf7fffffff 64bit pref] [ 0.189697] pci_bus 0005:01: resource 1 [mem 0x600c280000000-0x600c2ffefffff] [ 0.189733] pci_bus 0005:02: resource 1 [mem 0x600c280000000-0x600c2ffefffff] [ 0.189805] pci 0000:01:00.0: Adding to iommu group 0 [ 0.189841] pci 0000:01:00.1: Adding to iommu group 0 [ 0.189886] pci 0002:01:00.0: Adding to iommu group 1 [ 0.189921] pci 0003:01:00.0: Adding to iommu group 2 [ 0.189967] pci 0004:01:00.0: Adding to iommu group 3 [ 0.189993] pci 0004:01:00.1: Adding to iommu group 3 [ 0.190041] pci 0004:01:00.2: Adding to iommu group 3 [ 0.190095] pci 0005:02:00.0: Adding to iommu group 4 [ 0.190176] pci 0000:00:00.0: enabling device (0101 -> 0103) [ 0.190218] pci 0002:00:00.0: enabling device (0101 -> 0103) [ 0.190258] pci 0003:00:00.0: enabling device (0101 -> 0103) [ 0.190296] pci 0004:00:00.0: enabling device (0101 -> 0103) [ 0.190341] pci 0005:00:00.0: enabling device (0101 -> 0103) [ 0.190384] pci 0005:01:00.0: enabling device (0141 -> 0143) [ 0.191270] EEH: PCI Enhanced I/O Error Handling Enabled [ 0.192863] cpuidle-powernv: Default stop: psscr = 0x0000000000000330,mask=0x00000000003003ff [ 0.192885] cpuidle-powernv: Deepest stop: psscr = 0x0000000000300375,mask=0x00000000003003ff [ 0.192900] cpuidle-powernv: First stop level that may lose SPRs = 0x4 [ 0.192935] cpuidle-powernv: First stop level that may lose timebase = 0x16 [ 0.194993] HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages [ 0.195012] HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages [ 0.197207] pci 0000:01:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 0.197241] pci 0005:02:00.0: vgaarb: VGA device added: decodes=io+mem,owns=none,locks=none [ 0.197267] pci 0000:01:00.0: vgaarb: bridge control possible [ 0.197279] pci 0005:02:00.0: vgaarb: bridge control possible [ 0.197296] pci 0005:02:00.0: vgaarb: setting as boot device (VGA legacy resources not available) [ 0.197321] vgaarb: loaded [ 0.197596] pps_core: LinuxPPS API ver. 1 registered [ 0.197622] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti [ 0.197683] PTP clock support registered [ 0.197710] EDAC MC: Ver: 3.0.0 [ 0.198158] clocksource: Switched to clocksource timebase [ 0.215228] VFS: Disk quotas dquot_6.6.0 [ 0.215266] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 0.215314] *** VALIDATE hugetlbfs *** [ 0.217803] NET: Registered protocol family 2 [ 0.218044] tcp_listen_portaddr_hash hash table entries: 32768 (order: 7, 524288 bytes) [ 0.218429] TCP established hash table entries: 524288 (order: 10, 4194304 bytes) [ 0.219668] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 0.219859] TCP: Hash tables configured (established 524288 bind 65536) [ 0.220005] UDP hash table entries: 32768 (order: 8, 1048576 bytes) [ 0.220318] UDP-Lite hash table entries: 32768 (order: 8, 1048576 bytes) [ 0.220661] NET: Registered protocol family 1 [ 0.220686] NET: Registered protocol family 44 [ 0.220735] pci 0003:01:00.0: enabling device (0140 -> 0142) [ 0.220878] PCI: CLS 0 bytes, default 128 [ 0.220948] Trying to unpack rootfs image as initramfs... [ 6.392127] Freeing initrd memory: 51676K [ 6.400852] Initialise system trusted keyrings [ 6.400920] workingset: timestamp_bits=38 max_order=24 bucket_order=0 [ 6.403066] zbud: loaded [ 6.403564] Key type asymmetric registered [ 6.403576] Asymmetric key parser 'x509' registered [ 6.403594] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 244) [ 6.403687] io scheduler mq-deadline registered [ 6.403699] io scheduler kyber registered [ 6.403771] io scheduler bfq registered [ 6.404652] pci 0005:02:00.0: enabling device (0141 -> 0143) [ 6.404677] Using unsupported 1024x768 (null) at 600c280010000, depth=32, pitch=4096 [ 6.404785] fbcon: Deferring console take-over [ 6.404807] fb0: Open Firmware frame buffer device on /pciex@600c3c0500000/pci@0/pci@0/vga@0 [ 6.404998] hvc0: raw protocol on /ibm,opal/consoles/serial@0 (boot console) [ 6.405016] hvc0: No interrupts property, using OPAL event [ 6.405369] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled [ 6.405742] Non-volatile memory driver v1.3 [ 6.406319] libphy: Fixed MDIO Bus: probed [ 6.406330] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de [ 6.406728] mousedev: PS/2 mouse device common for all mice [ 6.450198] rtc-opal opal-rtc: registered as rtc0 [ 6.450698] powernv-cpufreq: cpufreq pstate min 0x63 nominal 0x30 max 0x0 [ 6.450719] powernv-cpufreq: Workload Optimized Frequency is enabled in the platform [ 6.452814] ledtrig-cpu: registered to indicate activity on CPUs [ 6.453077] NET: Registered protocol family 10 [ 6.457254] Segment Routing with IPv6 [ 6.457283] NET: Registered protocol family 17 [ 6.457314] Key type dns_resolver registered [ 6.457339] drmem: No dynamic reconfiguration memory found [ 6.458658] registered taskstats version 1 [ 6.458665] Loading compiled-in X.509 certificates [ 6.458706] zswap: loaded using pool lzo/zbud [ 6.458760] pstore: Using crash dump compression: deflate [ 6.498618] rtc-opal opal-rtc: setting system clock to 2019-12-02T01:23:43 UTC (1575249823) [ 6.499702] Freeing unused kernel memory: 4020K [ 6.499719] This architecture does not have kernel memory protection. [ 6.499728] Run /init as init process [ 6.629324] loop: module loaded [ 6.638064] dracut: root was live:CDLABEL=VOID_LIVE, is now live:/dev/disk/by-label/VOID_LIVE [ 6.702139] device-mapper: uevent: version 1.0.3 [ 6.702231] device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: dm-devel@redhat.com [ 6.718826] systemd-udevd[550]: starting version 3.2.8 [ 6.719034] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.719065] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.719086] random: systemd-udevd: uninitialized urandom read (16 bytes read) [ 6.720584] udevd[551]: starting eudev-3.2.8 [ 6.758438] dracut: rd.md=0: removing MD RAID activation [ 6.796280] Linux agpgart interface v0.103 [ 6.796997] synth uevent: /devices/vio: failed to send uevent [ 6.797015] vio vio: uevent: failed to send synthetic uevent [ 6.801890] tg3.c:v3.137 (May 11, 2014) [ 6.801911] tg3 0004:01:00.0: enabling device (0140 -> 0142) [ 6.802937] SCSI subsystem initialized [ 6.804844] usbcore: registered new interface driver usbfs [ 6.804881] usbcore: registered new interface driver hub [ 6.804968] usbcore: registered new device driver usb [ 6.807607] crypto_register_alg 'aes' = 0 [ 6.811045] crypto_register_alg 'cbc(aes)' = 0 [ 6.811678] crypto_register_alg 'ctr(aes)' = 0 [ 6.813277] crypto_register_alg 'xts(aes)' = 0 [ 6.814092] xhci_hcd 0003:01:00.0: xHCI Host Controller [ 6.814108] xhci_hcd 0003:01:00.0: new USB bus registered, assigned bus number 1 [ 6.814215] xhci_hcd 0003:01:00.0: hcc params 0x0270f06d hci version 0x96 quirks 0x0000000004000000 [ 6.814854] hub 1-0:1.0: USB hub found [ 6.814875] hub 1-0:1.0: 4 ports detected [ 6.815014] xhci_hcd 0003:01:00.0: xHCI Host Controller [ 6.815027] xhci_hcd 0003:01:00.0: new USB bus registered, assigned bus number 2 [ 6.815058] xhci_hcd 0003:01:00.0: Host supports USB 3.0 SuperSpeed [ 6.815091] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 6.815231] hub 2-0:1.0: USB hub found [ 6.815266] hub 2-0:1.0: 4 ports detected [ 6.815398] ahci 0002:01:00.0: enabling device (0541 -> 0543) [ 6.823475] fb0: switching to astdrmfb from OFfb vga [ 6.823825] [drm] platform has no IO space, trying MMIO [ 6.823843] [drm] Using device-tree for configuration [ 6.823852] [drm] AST 2500 detected [ 6.823871] [drm] Using Sil164 TMDS transmitter [ 6.823882] [drm] dram MCLK=800 Mhz type=7 bus_width=16 size=01000000 [ 6.824025] [TTM] Zone kernel: Available graphics memory: 32956200 KiB [ 6.824045] [TTM] Zone dma32: Available graphics memory: 2097152 KiB [ 6.824062] [TTM] Initializing pool allocator [ 6.825744] ahci 0002:01:00.0: AHCI 0001.0000 32 slots 4 ports 6 Gbps 0xf impl SATA mode [ 6.825757] ahci 0002:01:00.0: flags: 64bit ncq sntf led only pmp fbs pio slum part sxs [ 6.826770] scsi host0: ahci [ 6.827565] scsi host1: ahci [ 6.827711] scsi host2: ahci [ 6.827839] scsi host3: ahci [ 6.827911] ata1: SATA max UDMA/133 abar m2048@0x600c100010000 port 0x600c100010100 irq 30 [ 6.827936] ata2: SATA max UDMA/133 abar m2048@0x600c100010000 port 0x600c100010180 irq 30 [ 6.827956] ata3: SATA max UDMA/133 abar m2048@0x600c100010000 port 0x600c100010200 irq 30 [ 6.827975] ata4: SATA max UDMA/133 abar m2048@0x600c100010000 port 0x600c100010280 irq 30 [ 6.828307] tg3 0004:01:00.0 eth0: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 2c:09:4d:00:09:96 [ 6.828355] tg3 0004:01:00.0 eth0: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 6.828410] tg3 0004:01:00.0 eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 6.828438] tg3 0004:01:00.0 eth0: dma_rwctrl[00000000] dma_mask[64-bit] [ 6.828653] tg3 0004:01:00.1: enabling device (0140 -> 0142) [ 6.828916] fbcon: Deferring console take-over [ 6.828957] ast 0005:02:00.0: fb0: astdrmfb frame buffer device [ 6.844823] tg3 0004:01:00.1 eth1: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 2c:09:4d:00:09:97 [ 6.844845] tg3 0004:01:00.1 eth1: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 6.844858] tg3 0004:01:00.1 eth1: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 6.844868] tg3 0004:01:00.1 eth1: dma_rwctrl[00000000] dma_mask[64-bit] [ 6.844985] tg3 0004:01:00.2: enabling device (0140 -> 0142) [ 6.859343] tg3 0004:01:00.2 eth2: Tigon3 [partno(BCM95719) rev 5719001] (PCI Express) MAC address 2c:09:4d:00:09:98 [ 6.859363] tg3 0004:01:00.2 eth2: attached PHY is 5719C (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[1]) [ 6.859376] tg3 0004:01:00.2 eth2: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[1] TSOcap[1] [ 6.859386] tg3 0004:01:00.2 eth2: dma_rwctrl[00000000] dma_mask[64-bit] [ 6.860043] tg3 0004:01:00.1 enP4p1s0f1: renamed from eth1 [ 6.898163] [drm] Initialized ast 0.1.0 20120228 for 0005:02:00.0 on minor 0 [ 6.907361] [drm] amdgpu kernel modesetting enabled. [ 6.907403] amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 0: 0x6000000000000 -> 0x60001ffffffff [ 6.907426] amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 2: 0x6000200000000 -> 0x60002001fffff [ 6.907448] amdgpu 0000:01:00.0: remove_conflicting_pci_framebuffers: bar 5: 0x600c000000000 -> 0x600c00003ffff [ 6.907483] amdgpu 0000:01:00.0: enabling device (0540 -> 0542) [ 6.907576] [drm] initializing kernel modesetting (POLARIS10 0x1002:0x67DF 0x1462:0x3418 0xE7). [ 6.907600] [drm] register mmio base: 0x00000000 [ 6.907619] [drm] register mmio size: 262144 [ 6.907644] [drm] PCI I/O BAR is not found. [ 6.907661] [drm] add ip block number 0 [ 6.907668] [drm] add ip block number 1 [ 6.907675] [drm] add ip block number 2 [ 6.907682] [drm] add ip block number 3 [ 6.907707] [drm] add ip block number 4 [ 6.907714] [drm] add ip block number 5 [ 6.907730] [drm] add ip block number 6 [ 6.907755] [drm] add ip block number 7 [ 6.907771] [drm] add ip block number 8 [ 6.907803] [drm] UVD is enabled in VM mode [ 6.907819] [drm] UVD ENC is enabled in VM mode [ 6.907845] [drm] VCE enabled in VM mode [ 6.910225] tg3 0004:01:00.0 enP4p1s0f0: renamed from eth0 [ 7.140508] ata1: SATA link down (SStatus 0 SControl 300) [ 7.154157] usb 1-1: new full-speed USB device number 2 using xhci_hcd [ 7.252095] amdgpu 0000:01:00.0: GPU pci config reset [ 7.252212] [drm] GPU posting now... [ 7.302164] ata2: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.302187] ata4: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.302226] ata3: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.302330] ata2.00: ATA-9: Seagate BarraCuda SSD ZA500CM10002, STAS1024, max UDMA/133 [ 7.302351] ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 7.302418] ata3.00: ATA-9: Seagate BarraCuda SSD ZA1000CM10002, STAS1024, max UDMA/133 [ 7.302464] ata3.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 7.302488] ata4.00: ATA-9: Seagate BarraCuda SSD ZA1000CM10002, STAS1024, max UDMA/133 [ 7.302501] ata4.00: 1953525168 sectors, multi 16: LBA48 NCQ (depth 32), AA [ 7.302702] ata2.00: configured for UDMA/133 [ 7.302744] ata3.00: configured for UDMA/133 [ 7.302770] ata4.00: configured for UDMA/133 [ 7.302848] scsi 1:0:0:0: Direct-Access ATA Seagate BarraCud 1024 PQ: 0 ANSI: 5 [ 7.303131] scsi 2:0:0:0: Direct-Access ATA Seagate BarraCud 1024 PQ: 0 ANSI: 5 [ 7.303395] scsi 3:0:0:0: Direct-Access ATA Seagate BarraCud 1024 PQ: 0 ANSI: 5 [ 7.304738] sd 1:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/466 GiB) [ 7.304773] sd 1:0:0:0: [sda] Write Protect is off [ 7.304775] sd 2:0:0:0: [sdb] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 7.304816] sd 2:0:0:0: [sdb] Write Protect is off [ 7.304826] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.304834] sd 3:0:0:0: [sdc] 1953525168 512-byte logical blocks: (1.00 TB/932 GiB) [ 7.304845] sd 3:0:0:0: [sdc] Write Protect is off [ 7.304868] sd 3:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.304943] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 7.305934] sdb: sdb1 sdb2 sdb3 sdb4 [ 7.306662] sd 2:0:0:0: [sdb] Attached SCSI removable disk [ 7.306686] sda: sda1 sda2 sda3 [ 7.307183] sdc: sdc1 sdc2 sdc3 [ 7.307441] sd 1:0:0:0: [sda] Attached SCSI removable disk [ 7.307921] sd 3:0:0:0: [sdc] Attached SCSI removable disk [ 7.379553] hidraw: raw HID events driver (C) Jiri Kosina [ 7.420336] usbcore: registered new interface driver usbhid [ 7.420354] usbhid: USB HID core driver [ 7.420728] usbcore: registered new interface driver usbkbd [ 7.421739] input: Razer Razer BlackWidow Ultimate as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-1/1-1:1.0/0003:1532:010D.0001/input/input0 [ 7.434249] usb 2-4: new SuperSpeed Gen 1 USB device number 2 using xhci_hcd [ 7.460930] usb-storage 2-4:1.0: USB Mass Storage device detected [ 7.461079] scsi host4: usb-storage 2-4:1.0 [ 7.461155] usbcore: registered new interface driver usb-storage [ 7.461867] usbcore: registered new interface driver uas [ 7.478209] hid-generic 0003:1532:010D.0001: input,hidraw0: USB HID v1.11 Keyboard [Razer Razer BlackWidow Ultimate] on usb-0003:01:00.0-1/input0 [ 7.478401] input: Razer Razer BlackWidow Ultimate System Control as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-1/1-1:1.1/0003:1532:010D.0002/input/input1 [ 7.538193] input: Razer Razer BlackWidow Ultimate Consumer Control as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-1/1-1:1.1/0003:1532:010D.0002/input/input2 [ 7.538265] hid-generic 0003:1532:010D.0002: input,hidraw1: USB HID v1.11 Device [Razer Razer BlackWidow Ultimate] on usb-0003:01:00.0-1/input1 [ 7.538375] input: Razer Razer BlackWidow Ultimate as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-1/1-1:1.2/0003:1532:010D.0003/input/input3 [ 7.538486] hid-generic 0003:1532:010D.0003: input,hidraw2: USB HID v1.11 Mouse [Razer Razer BlackWidow Ultimate] on usb-0003:01:00.0-1/input2 [ 7.582150] usb 1-2: new low-speed USB device number 3 using xhci_hcd [ 7.606253] tg3 0004:01:00.2 enP4p1s0f2: renamed from eth2 [ 7.714119] [drm] RAS INFO: ras initialized successfully, hardware ability[0] ras_mask[0] [ 7.714140] [drm] vm size is 256 GB, 2 levels, block size is 10-bit, fragment size is 9-bit [ 7.714202] amdgpu 0000:01:00.0: BAR 2: releasing [mem 0x6000200000000-0x60002001fffff 64bit pref] [ 7.714215] amdgpu 0000:01:00.0: BAR 0: releasing [mem 0x6000000000000-0x60001ffffffff 64bit pref] [ 7.714253] pci 0000:00:00.0: BAR 15: releasing [mem 0x6000000000000-0x6003fbff0ffff 64bit pref] [ 7.714269] pci 0000:00:00.0: BAR 15: assigned [mem 0x6000000000000-0x60002ffffffff 64bit pref] [ 7.714281] amdgpu 0000:01:00.0: BAR 0: assigned [mem 0x6000000000000-0x60001ffffffff 64bit pref] [ 7.714299] amdgpu 0000:01:00.0: BAR 2: assigned [mem 0x6000200000000-0x60002001fffff 64bit pref] [ 7.714351] pci 0000:00:00.0: PCI bridge to [bus 01] [ 7.714361] pci 0000:00:00.0: bridge window [mem 0x600c000000000-0x600c07fefffff] [ 7.714371] pci 0000:00:00.0: bridge window [mem 0x6000000000000-0x6003fbff0ffff 64bit pref] [ 7.714390] amdgpu 0000:01:00.0: VRAM: 8192M 0x000000F400000000 - 0x000000F5FFFFFFFF (8192M used) [ 7.714401] amdgpu 0000:01:00.0: GART: 256M 0x000000FF00000000 - 0x000000FF0FFFFFFF [ 7.714413] [drm] Detected VRAM RAM=8192M, BAR=8192M [ 7.714420] [drm] RAM width 256bits GDDR5 [ 7.761214] [drm] amdgpu: 8192M of VRAM memory ready [ 7.761228] [drm] amdgpu: 8192M of GTT memory ready. [ 7.761266] [drm] GART: num cpu pages 65536, num gpu pages 65536 [ 7.761809] [drm] PCIE GART of 256M enabled (table at 0x000000F400000000). [ 7.761943] [drm] Chained IB support enabled! [ 7.763685] [drm] Found UVD firmware Version: 1.130 Family ID: 16 [ 7.764867] [drm] Found VCE firmware Version: 53.26 Binary ID: 3 [ 7.778042] [drm] DM_PPLIB: values for Engine clock [ 7.778057] [drm] DM_PPLIB: 300000 [ 7.778063] [drm] DM_PPLIB: 600000 [ 7.778068] [drm] DM_PPLIB: 918000 [ 7.778074] [drm] DM_PPLIB: 1167000 [ 7.778089] [drm] DM_PPLIB: 1239000 [ 7.778094] [drm] DM_PPLIB: 1282000 [ 7.778100] [drm] DM_PPLIB: 1326000 [ 7.778105] [drm] DM_PPLIB: 1366000 [ 7.778111] [drm] DM_PPLIB: Validation clocks: [ 7.778117] [drm] DM_PPLIB: engine_max_clock: 136600 [ 7.778147] [drm] DM_PPLIB: memory_max_clock: 200000 [ 7.778155] [drm] DM_PPLIB: level : 8 [ 7.778181] [drm] DM_PPLIB: values for Memory clock [ 7.778197] [drm] DM_PPLIB: 300000 [ 7.778202] [drm] DM_PPLIB: 1000000 [ 7.778217] [drm] DM_PPLIB: 2000000 [ 7.778231] [drm] DM_PPLIB: Validation clocks: [ 7.778247] [drm] DM_PPLIB: engine_max_clock: 136600 [ 7.778263] [drm] DM_PPLIB: memory_max_clock: 200000 [ 7.778288] [drm] DM_PPLIB: level : 8 [ 7.778800] [drm] Display Core initialized with v3.2.27! [ 7.795557] input: Logitech USB-PS/2 Optical Mouse as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-2/1-2:1.0/0003:046D:C00E.0004/input/input4 [ 7.795665] hid-generic 0003:046D:C00E.0004: input,hidraw3: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0003:01:00.0-2/input0 [ 7.796383] usbcore: registered new interface driver usbmouse [ 7.804273] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). [ 7.804293] [drm] Driver supports precise vblank timestamp query. [ 7.830683] [drm] UVD and UVD ENC initialized successfully. [ 7.922151] usb 1-3: new high-speed USB device number 4 using xhci_hcd [ 7.931623] [drm] VCE initialized successfully. [ 7.932580] [drm] fb mappable at 0x6000000530000 [ 7.932595] [drm] vram apper at 0x6000000000000 [ 7.932602] [drm] size 4325376 [ 7.932607] [drm] fb depth is 24 [ 7.932613] [drm] pitch is 5632 [ 7.932655] fbcon: Deferring console take-over [ 7.932675] amdgpu 0000:01:00.0: fb1: amdgpudrmfb frame buffer device [ 7.949841] [drm] Initialized amdgpu 3.32.0 20150101 for 0000:01:00.0 on minor 1 [ 7.992228] dracut: Scanning devices sdb4 sdc3 for LVM volume groups [ 7.996291] dracut: Reading all physical volumes. This may take a while... [ 8.066477] dracut: Found volume group "blackbird-vg" using metadata type lvm2 [ 8.066696] dracut: Found volume group "freya-vg" using metadata type lvm2 [ 8.087555] hub 1-3:1.0: USB hub found [ 8.087897] hub 1-3:1.0: 5 ports detected [ 8.099559] dracut: 5 logical volume(s) in volume group "blackbird-vg" now active [ 8.170500] dracut: 2 logical volume(s) in volume group "freya-vg" now active [ 8.218161] usb 1-4: new high-speed USB device number 5 using xhci_hcd [ 8.384446] hub 1-4:1.0: USB hub found [ 8.385179] hub 1-4:1.0: 4 ports detected [ 8.446486] usb 1-3.1: new high-speed USB device number 6 using xhci_hcd [ 8.468231] scsi 4:0:0:0: Direct-Access Kingston DataTraveler 3.0 PMAP PQ: 0 ANSI: 6 [ 8.470987] sd 4:0:0:0: [sdd] 121208832 512-byte logical blocks: (62.1 GB/57.8 GiB) [ 8.472118] sd 4:0:0:0: [sdd] Write Protect is off [ 8.473363] sd 4:0:0:0: [sdd] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 8.478835] sdd: sdd1 [ 8.481794] sd 4:0:0:0: [sdd] Attached SCSI removable disk [ 8.604181] input: OpenBMC virtual_input as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-3/1-3.1/1-3.1:1.0/0003:1D6B:0104.0005/input/input5 [ 8.663119] hid-generic 0003:1D6B:0104.0005: input,hidraw4: USB HID v1.01 Keyboard [OpenBMC virtual_input] on usb-0003:01:00.0-3.1/input0 [ 8.684685] input: OpenBMC virtual_input as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-3/1-3.1/1-3.1:1.1/0003:1D6B:0104.0006/input/input6 [ 8.684793] hid-generic 0003:1D6B:0104.0006: input,hidraw5: USB HID v1.01 Mouse [OpenBMC virtual_input] on usb-0003:01:00.0-3.1/input1 [ 8.698156] usb 1-4.4: new full-speed USB device number 7 using xhci_hcd [ 8.779907] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 8.842954] input: USB Sound Device as /devices/pci0003:00/0003:00:00.0/0003:01:00.0/usb1/1-4/1-4.4/1-4.4:1.3/0003:0D8C:0102.0007/input/input7 [ 8.902220] hid-generic 0003:0D8C:0102.0007: input,hidraw6: USB HID v1.00 Device [USB Sound Device ] on usb-0003:01:00.0-4.4/input3 [ 9.010229] EXT4-fs (dm-7): mounting ext3 file system using the ext4 subsystem [ 9.024213] EXT4-fs (dm-7): mounted filesystem with ordered data mode. Opts: (null) [ 9.072986] dracut: Mounted root filesystem /dev/mapper/live-rw [ 9.594760] dracut: Switching root - runit: $Id: 25da3b86f7bed4038b8a039d2f8e8c9bbcf0822b $: booting. - runit: enter stage: /etc/runit/1 => Welcome to Void! => Mounting pseudo-filesystems... [ 9.715624] random: crng init done [ 9.715645] random: 7 urandom warning(s) missed due to ratelimiting [ 10.185248] fuse: init (API version 7.31) [ 10.290144] raid6: vpermxor8 gen() 20467 MB/s [ 10.358146] raid6: vpermxor4 gen() 17690 MB/s [ 10.426147] raid6: vpermxor2 gen() 13343 MB/s [ 10.494144] raid6: vpermxor1 gen() 10234 MB/s [ 10.562146] raid6: altivecx8 gen() 12600 MB/s [ 10.630143] raid6: altivecx4 gen() 11932 MB/s [ 10.698146] raid6: altivecx2 gen() 9146 MB/s [ 10.766144] raid6: altivecx1 gen() 7211 MB/s [ 10.834151] raid6: int64x8 gen() 7180 MB/s [ 10.902146] raid6: int64x8 xor() 4814 MB/s [ 10.970146] raid6: int64x4 gen() 7180 MB/s [ 11.038148] raid6: int64x4 xor() 4174 MB/s [ 11.106147] raid6: int64x2 gen() 5296 MB/s [ 11.174151] raid6: int64x2 xor() 2735 MB/s [ 11.242161] raid6: int64x1 gen() 3377 MB/s [ 11.310143] raid6: int64x1 xor() 1771 MB/s [ 11.310157] raid6: using algorithm vpermxor8 gen() 20467 MB/s [ 11.310165] raid6: using intx1 recovery algorithm [ 11.323835] xor: measuring software checksum speed [ 11.362152] 8regs : 17364.000 MB/sec [ 11.402152] 8regs_prefetch: 15590.000 MB/sec [ 11.442152] 32regs : 17460.000 MB/sec [ 11.482152] 32regs_prefetch: 15649.000 MB/sec [ 11.522152] altivec : 20296.000 MB/sec [ 11.522160] xor: using function: altivec (20296.000 MB/sec) [ 11.682936] Btrfs loaded, crc32c=crc32c-vpmsum [ 11.720557] tun: Universal TUN/TAP device driver, 1.6 [ 11.765378] PPP generic driver version 2.4.2 [ 11.820439] VFIO - User Level meta-driver version: 0.3 [ 11.910200] Bluetooth: Core ver 2.22 [ 11.910221] NET: Registered protocol family 31 [ 11.910228] Bluetooth: HCI device and connection manager initialized [ 11.910239] Bluetooth: HCI socket layer initialized [ 11.910247] Bluetooth: L2CAP socket layer initialized [ 11.910256] Bluetooth: SCO socket layer initialized [ 11.987841] NET: Registered protocol family 40 => Loading kernel modules... => Starting udev and waiting for devices to settle... [ 12.198252] udevd[1228]: starting version 3.2.8 [ 12.215912] udevd[1229]: starting eudev-3.2.8 [ 12.253144] synth uevent: /devices/vio: failed to send uevent [ 12.253162] vio vio: uevent: failed to send synthetic uevent [ 12.439542] IPMI message handler: version 39.2 [ 12.450998] ipmi device interface [ 12.481565] at24 0-0050: 65536 byte 24c512 EEPROM, writable, 1 bytes/write [ 12.503218] ipmi-powernv ibm,opal:ipmi: IPMI message handler: The GUID response from the BMC was too short, it was 1 but should have been 17. Assuming GUID is not available. [ 12.526387] ipmi-powernv ibm,opal:ipmi: IPMI message handler: Found new BMC (man_id: 0x00cb06, prod_id: 0x0001, dev_id: 0x00) [ 12.528052] at24 2-0050: 16384 byte 24c128 EEPROM, writable, 1 bytes/write [ 12.550531] 5 fixed-partitions partitions found on MTD device flash@0 [ 12.550550] Creating 5 MTD partitions on "flash@0": [ 12.550558] 0x000000000000-0x000004000000 : "PNOR" [ 12.550694] 0x0000022a1000-0x000003821000 : "BOOTKERNEL" [ 12.550822] 0x000003944000-0x000003946000 : "VERSION" [ 12.550936] 0x000003989000-0x0000039c9000 : "IMA_CATALOG" [ 12.551026] 0x000003e10000-0x000003e8b000 : "BOOTKERNFW" [ 12.551041] mtd: partition "BOOTKERNFW" doesn't end on an erase/write block -- force read-only [ 12.565310] at24 3-0050: 256 byte spd EEPROM, read-only, 0 bytes/write [ 12.565840] at24 4-0054: 256 byte spd EEPROM, read-only, 0 bytes/write [ 12.770569] snd_hda_intel 0000:01:00.1: enabling device (0540 -> 0542) [ 12.770592] snd_hda_intel 0000:01:00.1: Force to snoop mode by module option [ 12.818474] media: Linux media interface: v0.10 [ 12.832170] input: HDA ATI HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input8 [ 12.832286] input: HDA ATI HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input9 [ 12.832457] input: HDA ATI HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input10 [ 12.832753] input: HDA ATI HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input11 [ 12.833005] input: HDA ATI HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input12 [ 12.833182] input: HDA ATI HDMI HDMI/DP,pcm=11 as /devices/pci0000:00/0000:00:00.0/0000:01:00.1/sound/card0/input13 [ 12.954414] usb 1-4.4: current rate 30464 is different from the runtime rate 96000 [ 12.982926] usb 1-4.4: Warning! Unlikely big volume range (=8065), cval->res is probably wrong. [ 12.982944] usb 1-4.4: [9] FU [Mic Playback Volume] ch = 2, val = -6144/1921/1 [ 12.988928] usb 1-4.4: Warning! Unlikely big volume range (=8065), cval->res is probably wrong. [ 12.988941] usb 1-4.4: [11] FU [Line Playback Volume] ch = 2, val = -6144/1921/1 [ 13.006185] usb 1-4.4: Warning! Unlikely big volume range (=6928), cval->res is probably wrong. [ 13.006202] usb 1-4.4: [8] FU [Mic Capture Volume] ch = 2, val = -4096/2832/1 [ 13.012560] usb 1-4.4: Warning! Unlikely big volume range (=6928), cval->res is probably wrong. [ 13.012575] usb 1-4.4: [15] FU [Line Capture Volume] ch = 2, val = -4096/2832/1 [ 13.018561] usb 1-4.4: Warning! Unlikely big volume range (=6928), cval->res is probably wrong. [ 13.018579] usb 1-4.4: [2] FU [PCM Capture Volume] ch = 2, val = -4096/2832/1 [ 13.019785] usbcore: registered new interface driver snd-usb-audio => Setting up keymap to 'us'... => Remounting rootfs read-only... [ 13.161047] EXT4-fs (dm-7): re-mounted. Opts: (null) => Activating dmraid devices... no raid disks => Activating btrfs devices... Scanning for Btrfs filesystems => Activating LVM devices... 5 logical volume(s) in volume group "blackbird-vg" now active 2 logical volume(s) in volume group "freya-vg" now active => Activating encrypted devices... => Activating LVM devices for dm-crypt... 5 logical volume(s) in volume group "blackbird-vg" now active 2 logical volume(s) in volume group "freya-vg" now active => Checking filesystems: => Mounting rootfs read-write... [ 13.721286] EXT4-fs (dm-7): re-mounted. Opts: (null) => Mounting all non-network filesystems... => Initializing swap... => Initializing random seed... => Setting up loopback interface... => Setting up hostname to 'void-live'... => Loading sysctl(8) settings... * Applying /usr/lib/sysctl.d/10-void.conf ... kernel.core_uses_pid = 1 fs.protected_hardlinks = 1 fs.protected_symlinks = 1 kernel.kptr_restrict = 1 kernel.dmesg_restrict = 1 kernel.perf_event_paranoid = 2 kernel.kexec_load_disabled = 1 kernel.yama.ptrace_scope = 1 * Applying /etc/sysctl.conf ... => Initialization complete, running stage 2... - runit: leave stage: /etc/runit/1 - runit: enter stage: /etc/runit/2 runsvchdir: default: current. [ 13.955104] udevd[1399]: starting version 3.2.8 [ 14.065004] udevd[1399]: starting eudev-3.2.8 [ 14.138868] fbcon: Taking over console [ 14.153285] Console: switching to colour frame buffer device 128x48 [ 15.657279] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 15.657297] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 15.657307] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 15.665238] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 15.867712] 8021q: 802.1Q VLAN Support v1.8 [ 15.960181] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 15.962578] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 15.974666] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2 [ 15.974680] cfg80211: failed to load regulatory.db [ 16.297815] amdgpu 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none [ 17.357995] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 17.358015] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 17.358026] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 18.290431] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 18.627754] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 18.627772] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 18.627782] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 19.849456] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 19.849471] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 19.849481] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 21.101462] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 21.101481] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 21.101491] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 22.336930] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 22.336948] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 22.336958] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 23.642883] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 23.642904] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 23.642914] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 24.562496] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 24.901682] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 24.901702] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 24.901713] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 26.143558] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 26.143576] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 26.143587] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 27.410487] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 27.410508] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 27.410518] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 28.670884] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 28.670906] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 28.670917] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 29.915665] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 29.915679] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 29.915690] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 30.834486] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 31.148215] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 31.148235] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 31.148245] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 32.378692] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 32.378709] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 32.378719] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 33.631951] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 33.631964] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 33.631974] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 34.858312] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 34.858331] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 34.858341] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 36.107787] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 36.107802] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 36.107813] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 37.042486] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 37.342580] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 37.342594] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 37.342604] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 38.591460] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 38.591479] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 38.591489] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 39.814666] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 39.814682] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 39.814692] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 41.070580] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 41.070593] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 41.070603] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 42.302602] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 42.302620] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 42.302630] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 43.218426] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 43.558324] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 43.558340] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 43.558350] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 44.815776] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 44.815789] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 44.815799] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 46.036163] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 46.036181] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 46.036192] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 47.267490] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 47.267505] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 47.267515] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 48.504540] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 48.504560] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 48.504570] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 49.426491] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 49.725604] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 49.725622] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 49.725632] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 50.969963] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 50.969978] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 50.969988] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 52.203827] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 52.203847] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 52.203857] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 53.429214] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 53.429231] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 53.429241] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 54.660172] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 54.660186] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 54.660196] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 55.602497] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 55.882612] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 55.882631] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 55.882641] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 57.106645] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 57.106662] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 57.106672] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 58.377897] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 58.377911] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 58.377921] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 59.619472] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 59.619491] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 59.619501] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 60.862406] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 60.862421] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 60.862432] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 61.778490] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 62.095797] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 62.095811] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 62.095821] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 63.322691] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 63.322710] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 63.322720] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 64.547776] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 64.547792] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 64.547802] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 65.789531] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 65.789544] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 65.789554] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 67.031084] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 67.031103] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 67.031113] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 67.954486] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 68.275576] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 68.275593] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 68.275603] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 69.527524] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 69.527537] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 69.527547] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 70.761506] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 70.761524] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 70.761534] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 71.987924] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 71.987939] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 71.987949] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 73.225237] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 73.225256] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 73.225267] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 74.162487] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready [ 74.486702] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 74.486720] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 74.486730] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 75.730311] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 75.730326] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 75.730336] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 76.987751] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 76.987771] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 76.987781] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 78.218680] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 78.218697] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 78.218707] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 79.459750] tg3 0004:01:00.2 enP4p1s0f2: Link is up at 1000 Mbps, full duplex [ 79.459764] tg3 0004:01:00.2 enP4p1s0f2: Flow control is off for TX and off for RX [ 79.459774] tg3 0004:01:00.2 enP4p1s0f2: EEE is disabled [ 80.402493] IPv6: ADDRCONF(NETDEV_CHANGE): enP4p1s0f2: link becomes ready